Tips for installing a toilet bowl

Ceramic bowls placed on concrete or tiled floors and fastened with dowels, screws, or by sticking to the floor.Between the floor and the toilet are paving the rubber sheet with a hole for passage of a direct issuance of the toilet. Also permissible to mount toilet screws taffeta - a wooden board with a hole for the bell, clamped to the concrete.

Toilet bowl set as follows. Graduation sprout with external grooves smeared divorced in drying oil and red lead him tightly wound pitch strand. When winding a strand of not finishing the appendix of 3-4 mm to the ends of its falling into the hole process and not caused pollution.

Then lock promazyvayut top red lead, and toilet set a release processes in the bell. Check your installation toilet, it screws with screws to the studs. Screws need to screw up carefully so as not to chip the edge toilet attached to taffeta, to tighten the screws smeared axle grease. Under head screws enclose a piece of leather or rubber and metal washer.

Flush tank is mounted to the installation of a toilet bowl by two screws. Screws are mounted on the wall in the dowels so that the tank was strictly horizontally. Before installing the cistern to him on the floor has added flushing pipe diameter of 32 mm. The other end of the flushing pipes were coated with red lead and wrapped in linen strands which were coated with red lead from the top, too. At the end of the pipe wear rubber cuff, which is tied to the tube a thin wire. The other end wrench and tighten the cuffs on the pipe.

A wooden seat is bolted directly to the toilet. K underside of the seat screws, rubber buferki, protecting a toilet seat from damage during the fall of the seat.

When installing the Dish bowl with direct release of Issue toilet to connect directly with the funnel outlet pipe, which should be removed flush with the floor.

Installing Dish bowl with an oblique issue and vysokoraspolagaemym tank and adherence to the toilet water and sewer rising mains located in the sanitary blocks, or to the risers, located in the furrows of the wall are shown in the figure. The toilet bowl is installed in accordance with the mounting dimensions shown in the drawing.

Installing Dish bowl with the release of an oblique angle of 30 ° and extended shelf directly connected with the flushing toilet "Compact" is shown in the figure. Flushing cistern mounted on an elongated toilet ledge with two bolts. By the toilet privertyvayut special fittings for attaching the seat.

Installing Dish toilet with low-flushing toilet

Plate bowls with the release angle of 30 ° can connect to the sewage network in two ways. One way, when the toilet has added two-scene to a tee, which is part of the sewer risers. Another way is that the toilet to the sewage network associated with reduced tee, which is part of the outlet line. In the latter case, a toilet set with a slope of sewer risers.

The toilet bowl can be installed with the laying of the outlet pipe above the floor is open or plinth.

For fixing toilets to tile and concrete floors are widely used epoxy glue. Glue is applied to the bearing surface of a metal spatula toilet in four places on the corners in such a way that the total glued area was not less than 20 cm2. The thickness of the adhesive should be 4-5 mm. Then set the pan on the floor and pressed tightly to him.To ensure the necessary strength glue, toilet seats should be in a state of rest at least 10-12 hours

Surfaces are preparing to install toilets with the electrified instrument. During the processing of this tool to prepare the surface of corundum stone cause roughness, which contribute to a better adhesion toilets.

When using epoxy glue is necessary to perform the following safety rules: the premises, which shall be charged pipes should be equipped with ventilation system with a triple exchange of air in the room where the use of epoxy glue, is not permitted to store and eating, when working with glue to use protective paste for the hands, rubber gloves or mittens.

Skin hardener or finished adhesive wound site should be wiped with acetone, and then rinse with warm water.After working with glue, as well as during recess, you must wash your hands with warm water and soap.