Tips for staining the walls in the kitchen

Colors of the kitchen can be achieved by staining the walls. Since the kitchen - a place where mostly going the whole family, watch a selection of colors. It should be snug and comfortable, so the colors should not be overcrowded. You can pick up on the principle of contrast dye, using two or more colors, or paint only certain elements of the premises, such as skirting boards, windows, windows, heaters, etc. It is important to observe the measure, without violating the integrity of the image space, mindful of his appointment and set decorative items (curtains, potholders, etc.). Surfaces in the kitchen dye paint, enamel, glue or latex paint.

Oil paints are composed of pigments and fillers, worn on the drying oil. These advantages include the humidity and heat resistance. They almost do not break down when exposed to light, chemicals and disinfectants. Among the shortcomings can be noted toxicity, long drying time (up to 3 days) and leakage (not breathable). Pay attention to the price of ink: if it is very low, it probably says on its respective capacities.

Enamel paint - is colorful compositions prepared from a mixture of lacquer and pigments by grinding in kraskoterkah. Pigment for enamel paint is diluted in oil varnishes. Enamel paint with their advantages and disadvantages are similar in their properties in oils. The only difference enamel is that it dries faster than oil paint - up to 24 hours.

Lime-based paints are composed of a mixture of lime with water, table salt, or a combined drying oil. To give the cold shade of white tint added blue dye. A variety of paints on the basis of lime are distempers, in which, instead of lime added chalk. A significant advantage of such a paint is a low cost and the opportunity to cook it yourself.

Coatings of this material is well breathable and resistant to high temperatures. In addition, the paint layer is non-toxic, dries quickly. Disadvantage of lime paints is a weak resistance to high humidity (over time the paint layer, absorbing moisture from the surface with pieces falling off). In addition, painted surfaces exposed to abrasion.When you touch the wall you can get dirty.

In water-based paints are tiny plastic particles are added to the water. Evaporation formed strong elastic film.Dyes of this kind have a number of positive qualities: not toxic, breathable and water vapor. After drying the paint layer wall can be washed. Their use within the premises has many advantages relative to other colors. A significant advantage of latex paint is also an economical and hiding power - enough for 1 kg of staining area of 5 m2. And, finally, water-based paints can be applied to walls, formerly painted enamel, oil paint or glue, if this is not used alum or vitriol primer.
The disadvantages of latex paint is the relative fragility of the coating (2-3 years against 3-5 years enamel coating). Before you begin painting works directly prepare the surface. It must be flat, smooth and free of defects.

Before you cover the paint plaster or plaster walls, sand it with sandpaper or a pumice stone. If the surface of the wall has cracks and fissures, then they must be expanded, moisten with water and fill the grease.Irregularities and other defects, smooth the putty. After grinding zagruntuyte surface - this measure can reduce the porosity of the coating and prevent excessive absorption of paint.
Sales there are many kinds of primers for oil and water paints, but you can prepare them and ourselves.

Primers for adhesive and lime staining

At the 3 parts fat lime test take 0.25 of soap and 0,1 parts of linseed oil. Soap grind and pour a small amount of boiling water, in which it must be completely dissolved. Then in the hot soapy solution in small portions, pour all the varnish and mix thoroughly. Then add the lime paste, stir until smooth and strain. The resulting mixture was dilute with water to just received 10 liters of.

Kuporosnoye primer for adhesive staining

To prepare 10 liters of primers Take 150 g of copper sulfate, 250 g of soap, 200 grams of any animal glue, 30 g of linseed oil and 2 kg of crushed and sifted through a sieve of chalk. In 3 l of boiling water vsypte copper sulphate. Separately, 2 liters of water boil the glue. Nastrugannoe soap, add the other 2 liters of water. Then, the soap solution, mix with the glue mixture and pour it in small portions varnish. Mixture thoroughly. Thin stream add the solution of copper sulfate. Once fully cooled, add the composition of chalk and water in such a way as to obtain 10 l of primers, which then should filter.

For each 1 m2 of plaster wall in approximately 300 g of the primer, and 1 m2 of brick wall - 450

Before painting plastered walls with oil paint soaking them with a clean varnish, which prior to use, warm slightly, so that it is better absorbed into the surface, with the caution: linseed oil - flammable.

Stain the walls need from top to bottom. Dye, apply lime to wet the walls, and the second layer - only after the complete drying of the first.

Preparation of white oil paint to tint

Requires 1 kg sifted through a fine sieve chalk, 3 liters of water, 40 g of ultramarine, 70 g carpenter or tile adhesive. At 1.5 liters of water dissolve chalk. At the same time prepare the solution of ultramarine for 40 g of the substance of 1,5 l of water, then strain. Mortar mix and add the glue.

The quality Kohler affect the amount of glue: if it is not enough, the paint obmelivaetsya, and if his lot coverage after drying can be cracked. To check the quality of tint cover them part of the surface and allow to dry, then rub hand: good Kohler should not be greatly obmelivatsya. If this does happen, it means that you have added little glue, and if where you touch his hand, were brilliant band, then the mixture too much glue. To reduce the content of adhesive in Kohler, pour into it a little water.

Quality Kohler also depends on its viscosity. To check, take a wooden stick and dip in dye, and then remove.Good Kohler should cover stick solid layer and flow down to her thin continuous stream. Before use, Kohler filtered.

For latex paint is best to take a ready water-based pigment.